There are many different Rebel Sabers available in the market and some of them can be very expensive. When buying one, it is important to know a few things about them. These are: How to remove the blade plug, how to charge your saber, and how to change the batteries.
Charge Your Saber
If you want to know how to charge your rebel sabers, you need to be aware of its various parts. You can find a guide in the Lucifer Sabers user manual. It contains all the necessary information on how to charge your saber. The first step is to remove the blade. This will allow the saber to be transported easier. Once the blade has been removed, you will need to open up the saber to access the inside.
Then, unscrew the battery holder. To do this, you will need an Allen wrench. Also, make sure that you do not over tighten the screws. Otherwise, you may damage the batten. Next, insert the saber battery in with the positive side towards the buttons. If you do not have an Allen wrench, you can bend the tabs outward with a flat edge screwdriver.
Charge your saber by plugging in a charging cable. Be sure to use a 5v/2amp max wall charger. Your charging device must have a USB port. After a few hours, your saber will be charged. However, you need to be prepared to wait. Since sabers normally take around five to eight hours to charge, you need to be patient. When the battery is fully charged, your saber will be ready to use. The saber will play sound, cycle through the different sound fonts, and turn on music.
Remove The Blade Plug
To remove the blade plug on Rebel sabers you have to be careful. These rgb lightsaber have a lot of electronics and are very sensitive. You can damage your saber or the blade if you try to pull the blade plug out incorrectly.
The LEDs in the blade are very bright. They can hurt bystanders’ eyes if they stare at them directly. If you want to avoid this, make sure you don’t stare at the LEDs for more than a few seconds. When you have the LEDs in the blade on, you can cycle through different light effects. For example, you can change the color of the saber. This is done by pressing the button once.
In addition, a quick twist of the hilt can produce a special effect. It is also possible to turn off the LED. While you are not required to use a blade plug, it can be helpful to make the saber look as real as possible. There are several different types. Some are opaque and reduce the bleeding effect. Others are clear.
Regardless of the type, you should never try to force the blade plug into the socket. This can damage the blade or hilt. In some cases, a blade plug will get stuck in the blade socket. This is usually because the plug is slightly too big for the socket. A little sanding can help.
Change The Batteries
If you want to know how to change the batteries on a rebel saber, you have come to the right place. Changing the battery on a light saber is a quick and simple process. But before you start, you’ll want to check that the blade is still working. First, remove the old battery and replace it with the new one. Make sure to use the correct type and size for the model. For example, if your lightsaber has a thin neck, you should not use an old version of the battery that is meant for the thick-necked saber.
Next, you can charge the battery. You will need a charging device with a usb port. A 5v/2amp max wall charger is ideal. It can take approximately four hours to fully charge a battery. Once the battery has been charged, you can proceed to change the batteries on your lightsaber. Be careful when doing this because the blade can break out of the saber with significant force.
Before changing the batteries on a rebel saber, make sure to follow the proper procedures. The following tips will help you to do this without risking damage. When you change the batteries on a lightsaber, make sure to insert the battery with the positive side towards the buttons. If you insert the battery with the negative side, the battery will not work.
Conclusion
If you are looking for an easy way to add a new wargame to your collection, Rebel Sabers is a great option. Built on the Great Battles of the American Civil War system, the game allows you to play as cavalrymen in four historical battles. And, it works with previous GBACW games, too.